Cat Penanda Jalan Termoplastik JT/T 280
JT/T 280 ialah spesifikasi industri pengangkutan China bagi cat penanda turapan — teks di sebalik rangkaian lebuh raya terbesar di dunia, diterbitkan semula pada tahun 2022 dengan had minimum yang lebih tinggi: cat leburan panas kini mesti mengandungi sekurang-kurangnya 30% manik kaca pracampur. Inilah piawaian yang membentuk pengalaman kami, dan piawaian yang dirujuk oleh projek kendalian kontraktor China di seluruh dunia. Produk ini dibuat untuk memenuhi JT/T 280-2022, jenis reflektif leburan panas.
- NAMA PRODUKCat penanda jalan termoplastik JT/T 280
- PIAWAIANJT/T 280-2022 — jenis leburan panas, reflektif
- PEMBUNGKUSAN25 kg / beg
- MANIK KACAPracampuran ≥ 30% — had minimum mandatori edisi 2022
- WARNAPutih / kuning · 10 warna ditakrifkan dalam piawaian
- TAKAT LEMBUT100 – 140 °C
- MASA KERING TANPA JEJAK TAYAR≤ 5 min
- TEMPAT ASALGuangxi, China
Keperluan JT/T 280-2022
JT/T 280 dikeluarkan oleh Kementerian Pengangkutan China dan merangkumi setiap keluarga cat penanda — leburan panas, pelarut, dua komponen dan berasaskan air. Edisi 2022 menggantikan JT/T 280-2004 pada 9 Disember 2022. Semua kandungan di bawah memetik teks 2022 bagi keluarga leburan panas, iaitu kategori produk ini.
The 2022 edition raised the floor
Under the 2004 edition a factory could sell an “ordinary” hot-melt with no beads in the mix. The 2022 revision deleted that product outright — hot-melt now exists in exactly two types, and both must carry premix glass beads:
| Type | Premix glass beads | Form |
|---|---|---|
| Reflective (反光型) | ≥ 30% by mass, roundness per GB/T 24722 | Flat lines — this product |
| Raised / vibration (突起型) | ≥ 30% by mass | Profiled lines that rumble under the wheel |
The practical consequence: a “JT/T 280 hot-melt” offer with 10% or 20% beads — or none — is being quoted against a standard that no longer exists. If a tender written before 2023 still cites the 2004 edition, ask which text governs before comparing prices; the bead content alone moves the cost significantly.
Performance requirements — Table 3, reflective type
| Property | Requirement |
|---|---|
| Density | 1.8 – 2.3 g/cm³ |
| Softening point | 100 – 140 °C |
| No-track drying time | ≤ 5 min |
| Compressive strength | ≥ 12.0 MPa at 23 °C · ≥ 2.0 MPa at 60 °C |
| Abrasion loss | ≤ 80 mg |
| Low-temperature crack resistance | 3 cycles of −10 °C (4 h) / room temp (4 h) — no cracks |
| Heating stability | 4 h held at 200 ± 10 °C — no yellowing, scorching or clumping; colour stays within the standard’s chromaticity boxes |
| Fluidity | 90 ± 5 mm²/g |
| Thermal deformation resistance | ≥ 90% (60 °C, 50 kPa, 1 h) |
| Total organic content | ≥ 19.0% |
| Luminance factor | White ≥ 0.80 · yellow ≥ 0.48 (Table 2 coordinates) |
| Harmful substances | Per JT/T 1326-2020, the marking-material limits standard |
Two of these are worth reading twice. The double compressive test — cold and at 60 °C — is aimed at hot climates, where a line that is hard in the lab can still track and deform under summer traffic. And the 200 °C heating-stability hold simulates the kettle: four hours at working temperature without scorching or drifting off colour is what separates a line that stays white from one that yellows the day it is laid.
The recipe’s inputs are specified too
Where BS 3262 and AASHTO M249 mostly test the finished powder, JT/T 280-2022 goes a level deeper and writes normative specs for the raw materials themselves — Appendix A for the resin, Appendix B for the polyethylene wax:
| Input | Key requirements (2022 text) |
|---|---|
| Resin — C5 petroleum or rosin | Softening point ≥ 100 °C · Gardner colour ≤ 5.0 · melt viscosity ≤ 200 mPa·s at 200 °C · ash ≤ 0.1% · 4 h at 200 °C without darkening |
| Polyethylene wax | Softening point ≥ 100 °C · Gardner colour ≤ 5.0 · melt viscosity ≤ 100 mPa·s at 150 °C · needle penetration ≤ 10 (25 °C, 100 g) · ash ≤ 0.1% |
| Premix glass beads | Content ≥ 30% · gradation and roundness per GB/T 24722 |
This is the audit-the-inputs philosophy the Chinese network runs on, and it suits a factory like ours: the resin and wax arrive with their own test numbers, the mix leaves with the batch COA, and both paper trails point at the same standard.
The bag melts into the kettle
The most distinctive clause in the 2022 edition is the packaging: hot-melt paint shall be packed in a dedicated EVA sack (clause 8.2.1, Appendix C) that goes into the preheater with the paint. At 140 °C the stirred melt dissolves the whole bag within 3 minutes — no cutting, no emptying, no dust at the kettle, no pile of used bags on the roadside. The same film still has to survive logistics: 4 h at 90 °C without sticking, a 2.5 m stack for three days, a 2 m drop, all without splitting. Type I single-layer sacks hold 25.0 kg. Tell us at order whether your project runs the melt-in route — export orders that prefer a conventional woven outer bag can have one over the EVA liner.
JT/T 280, BS 3262, AASHTO M249 — which to cite
| JT/T 280-2022 | BS 3262 | AASHTO M249 | |
|---|---|---|---|
| Premix glass beads | ≥ 30% | ≥ 20% (reflectorized) | 30 – 40% |
| Who cites it | China’s network; Chinese-contracted projects abroad | UK-legacy markets — Middle East, SE Asia, Africa | US-influenced markets |
| Distinctive feature | Input specs + melt-in EVA bag | The long-standing trade default | Named binder recipe |
On bead content the three standards agree more than they differ — the JT/T 280 floor of 30% sits inside the AASHTO band and above the British one. If your engineer is a Chinese contractor, the tender almost certainly says JT/T 280 and this is the page to quote from; for BS or AASHTO texts, see the related products below. Either way, name the edition year in the contract.
Dari Talian Kami Ke Pelabuhan Anda
- 25 kg setiap beg — beg EVA yang dimasukkan semasa peleburan mengikut Lampiran C piawaian, dengan beg luar tenunan konvensional tersedia untuk pengendalian eksport; mulut beg dikedapkan rapat seperti yang dikehendaki oleh klausa 8.2.1.
- Ditanda dan didokumenkan mengikut piawaian — nama produk, nombor dan jenis piawaian, berat bersih, nombor kelompok, tarikh dan tempoh penyimpanan, dengan sijil pematuhan dalam penghantaran.
- Setiap kelompok lulus ujian makmal dalaman — kebendaliran, takat lembut, warna dan masa tanpa jejak tayar — sebelum disusun untuk pemuatan, serta dihantar bersama COA.
- Dihantar dari Pelabuhan Qinzhou — Asia Tenggara dalam 5–15 hari, Afrika dan benua Amerika secara purata ~30 hari. Terma perdagangan EXW / FOB / CIF.
- Manik tabur permukaan dimuatkan dalam kontena yang sama — satu penghantaran, satu set dokumen, sedia untuk taburan berganda yang dikehendaki oleh helaian spesifikasi.
Dipadankan Dengan
Soalan Pembelian
Q-01Our tender just says “JT/T 280 hot-melt” — what do we get?
The current edition, JT/T 280-2022, hot-melt reflective type — which means at least 30% premix glass beads by mass. Be aware that the 2004 edition allowed an “ordinary” unbeaded hot-melt that the 2022 revision deleted: if a competing offer is cheaper because it carries few or no premix beads, it is being quoted against a dead text. Ask every supplier to state the edition and the bead content, then compare.
Q-02What is the melt-in EVA bag about?
JT/T 280-2022 requires hot-melt paint to be packed in a dedicated EVA sack that is thrown into the preheater whole — the stirred melt dissolves the film within about 3 minutes at 140 °C. The crew never opens a bag, there is no powder dust at the kettle and no bag waste on site. State at order whether your project wants the melt-in route; a woven outer bag can be added for rough export handling.
Q-03Can you supply the other colours in the standard?
White and yellow are the running colours, and the 2022 edition defines ten — including orange, red, green, blue, grey and black — with chromaticity boxes and luminance factors for each. If your project needs a colour beyond white and yellow, ask: coloured formulations are quoted per order against the same Table 2 coordinates.
Q-04Which trade terms do you support?
We can provide EXW, FOB, CIF services, etc.
Dapatkan Sebut Harga Dalam 24 Jam
Sila isi borang di bawah dan kami akan menghubungi anda.
